Tools & Lab equipment

A multimeter is a tool without no electrician can work, but when these little tools appear we ask ourselves what can we do without them! Give this components tester almost anything and it will tell you which component it is and even some more details about it! For example, you connect a resistor on it and it will show it is a resistor and give you his value in ohms. same goes for capacitors and inductors. Give it NPN or PNP transistor it will hFE and Vf. For diodes, it will tell you its voltage drop and capacity. The most interesting is that the tool will know which component is connected.

Classic and simple cutting pliers for cutting off excess material after soldering. Those can also be used for wire cutting or insulation removing.

High-quality spare probes for a multimeter.

If the soldering iron isn’t clean, neither will the the solder joint. This cleaning net allows quick tip cleaning by “stabbing” the soldering iron in it. When the net is filled with solder, simply remove it from the casing, clean the excess solder, return it back and use it again!

To pick up ultra-small components and put them in the right place you simply have to own a right tool. One such are the tweezers for SMD components which will enable you to handle 0603 components. With little more exercise even smaller ones, won’t be an issue. Of course, the tweezers are ESD safe so you shouldn’t worry that something will happen to your components.

The SMD components are very small and the tweezers help us to do the job properly. And what should we do when we are having larger components, such as integrated circuits that can be so large that we can not grab them with tweezers? SMD vacuum tweezer will help us here. It uses a vacuum to grab the surface of IC. The vacuum is activated by pressing a small button, so using this tool won’t be a problem. It comes with several tips for different integrated circuits.

This is a huge roll of soldering wire. It’s a copper-plated stranded wire that comes in a thickness of 30AWG. Ideal for connecting to a protoboard or inside a project box. If you decide to buy this roll, you’ve probably solved the wire problem for at least 10 years!

• Thickness: 30AWG (0.255mm cross-section)
• Lenght: 250m
• Wire color: crvena, žuta, plava, crna ili bijela
• Stranded copper-plated wire

Once you learn how to solder, you notice that your soldering isn’t perfect. Desoldering pump is a tool that should be on the table of each maker/electronics engineer because it allows easy removal of excess solder, thus repairing short circuits or removing the components from the board. It works on the principle of “sucking in” the solder (liquid state) inside itself. It is completely safe to use.

Well known protoboard 2 x 8 cm. Can be used for all of the ongoing mergers and soldering. Very good quality.

Banana connectors are quite standard connectors in electronic labs because they allow fast and firm connection.

Desoldering wick is a very practical tool for every workshop. It’s a braided copper wire, soaked in flux, so it catches solder effectively. If you have a spot from which you need to remove the solder, this strip will do a great job. Unlike the discharge pump, this strip can completely remove the solder from a hole or a pad. 1.5m should last long since you spend only one or two centimeters per one desoldering.

• Lenght: 1.5m
• Width: 1.9mm

Banana connectors are a pretty standard type of connection inside electronic labs because they provide fast and firm connection.

Banana connectors are a pretty standard type of connection inside electronic labs because they provide fast and firm connection.

• Diameter: 4mm
• Color: red
• Male connector

Banana connectors are a pretty standard type of connection inside electronic labs because they provide fast and firm connection.

• Diameter: 4mm
• Color: black
• Male connector

Aligator clips are practical for quick connections during prototyping/testing. You can solder any type of wires to these clips.

Aligator clips are practical for quick connections during prototyping/testing. You can solder any type of wires to these clips.

Aligator clips are practical for quick connections during prototyping/testing. You can solder any type of wires to these clips.

Aligator clips are practical for quick connections during prototyping/testing. You can solder any type of wires to these clips.

thermocouple sensor is a temperature measuring device, with its range usually bigger than standard sensors. If you’ve ever bought a multimeter and got some kind of temperature sensor, that is the thermocouple.

This Protoboard 12×8 cm is a durable, high-quality prototyping board ideal for moving from breadboard testing to permanent circuit construction. Measuring 120×80 mm, it provides ample space for complex projects, supporting engineers, hobbyistsin building reliable, long-lasting electronic devices. Its robust construction ensures stable soldering and performance across a wide range of applications.
 
Made from fibreglass with a standard pre-drilled grid, the board features a solder mask on both sides to prevent bridges and improve reliability. Silkscreened row and column markings simplify component placement and debugging. Its generous size accommodates numerous I/O pins, power circuits, and multiple ICs, while remaining suitable for enclosures.
 
Perfect for custom shields, permanent prototypes, or small-scale production, the Protoboard 12×8 cm supports through-hole components and can adapt to SMD parts via breakout adapters. Add this versatile board to finalize your project with a clean, professional, and dependable platform.