Shop

Screw terminal for PCBs with a width of 3.5mm pin with two contacts.

The classic Micro USB cable which fits most modern Android smartphones, but also our new development boards.

ESP8266 is an IC that delivers a true revolution in the world of makers, especially in the world of IoT (Internet of Things). This is a complete 32-bit SoC (System on Chip) with built-in flash memory, frame and EEPROM which can even be programmed directly from the Arduino interface, without the need for additional micro-controller. With all this, the most important point is that in itself has a built-in WiFi (AP, STA, AP + STA), all that for “little money”.

ESP8266 in this form (ESP-12) is suitable for direct soldering to a printed circuit board as an SMD component or directly solder the wires since the pin has its holes. It also comes with a PCB trace antenna.

Note: ESP8266 is an IC that works at 3.3V! Connecting directly to 5V, or track Arduino or Croduino plate will destroy it! Use logic level converter.

Commonly used in a ceramic capacitor performance – Capacitor 100nF always come in handy 🙂

5mm RGB LEDs in a classic through-hole version with 4 pins. Each one representing one color (+), while the longest pin being a common cathode (common negative) for all three colors.

A 7-segment display is classical, often used and already familiar component. Size of a digit on the display is 0.56inch and the light it transmits is red. The display has a common cathode.

7-segment display is classical with common cathode, often used and already familiar component. Size of the digit on the display is 0.56inch and the light it transmits is red. The display has a common cathode.

A 7-segment display is a classic, often used and already familiar component. The size of the digit on the display is 0.56inch and the light it transmits is red. The display has a common cathode.

If you use some laboratory equipment such as power source, signal generators or, in most cases, multimeters – you’ll find this cable very practical. It has 2 banana connectors – on one end so you could connect it to mentioned devices and on another end to connect it to alligator connector which allows you to connect to almost anything!

Connecting to other devices and controllers from improvised power sources becomes truly simple with this terminal. Just use a screwdriver to tighten your wires to the terminal and you’re ready!

Connecting to many other devices and controllers from improvised power sources becomes truly simple with this terminal. Just use a screwdriver to tighten your wires to the terminal and you’re ready!

LM 7805 is often used 5V linear regulator, this one is in the THT version.

A through-hole holder for CR2032 3V battery which you can find on watches,  RTCs, toys, motherboard and other electronics.

BR2032 batteries are also suitable for this holder, but we do have one more battery type for you – CR2032 battery.

SMD Battery Holder for CR1220 3V battery, just like the one on our Croduino Damba.

Dasduino Beginner Kit is a complete system for learning how to code and getting familiar with the main principles of electronics. With this set, you’ll be able to code the world and different electronic gadgets around you. Moreover, you’ll learn how to code your Dasduino (Arduino compatible board) in C programming language, connect electronic components and other things of importance in the electronics world. The best thing about this kit is that no experience in coding or electronics is required to get started.

This kit is an amazing choice for not only beginners, but schools, businesses, hobbyists and even colleges because it offers everything that is necessary for a individual to learn about electronics through their own project, while being at an affordable price.

Hobby version of Dasduino Beginner Kit has much more components than the basic version of the kit. It contains additional components and other actuators and sensors.

This kit consists of:

• Dasduino CORE + USB cable
• Set of cables for breadboard
• Breadboard
• 15x 10K resistor
• 25x 330ohm resistor
• 2x 5mm RGB LED diode
• 6x 5mm blue LED diode
• 6x 5mm red LED diode
• 6x 5mm yellow LED diode
• 6x 5mm green LED diode
• DHT
• 3x Photoresistor
• 6x Pushbutton
• Buzzer
• 3x MOSFET transistor IRF540
• 3x 2N2222 transistor
• Shift register 74HC595
• 6x Potentiometer 10k
• 3x Big pushbutton
• Relay, 1-channel
• LCD display 16×2
• 3x 1N4148 diode
• Ultrasonic distance sensor
• Motion sensor HC-SR501