Components

GSM PCB antenna with IPX connector for connection on your boards that use an IPX connector.

This antenna connects you to 4G/LTE network it connects on your device via an IPX connector.

• Frequency: 4GHz/LTE
• Dimensions: 40 x 15 x 0.25mm
• Cable lenght: 12cm

IPX SMD connector for soldering to the printed circuit board. It is most commonly used with antennas, and the impedance is 50 ohms.

If you have a device you want to connect to a WiFi network, by using an IPX connector, all you need is this antenna. Use the IPX connector to establish connection with your device and it is ready to connect to a 2.4GHz WiFi network.

SPST (single-pole, single-throw) is a simple switch that connects or disconnects the two contacts in its casing.

• Type: SPST
• Shape: box
• Max. current/voltage: 250VAC 10A
• Dimensions: 17mm x 13mm x 11mm (without contacts)

Generic P-channel MOSFET transistor in DPAK package. Generic implies that the exact part number may vary, but the transistor will always be equal to or better than the parameters below.

• Vdss: -30V
• Vgs: -2.1V
• Rds(on): 0.068ohm
• Id: -30A
• Package: DPAK
• Components example: HY19P03

M4 rectifying diode inside SMAF package. Often used to adjust voltage and protect against reversed polarity.

SPDT (single-pole, dual-throw) is simple switch which connects central contact with one of the other two contacts located inside its housing.

Caps for THT potentiometer from our store that would make control much easier and would simply just look better.

A 1M variable resistance potentiometer that fits the breadboard, but can also be built into the case due to the increased size. They can be used for various types of control, eg. adjusting how bright the LED is.

A 100k variable resistance potentiometer that fits the breadboard, but can also be built into the case due to the increased size. They can be used for various types of control, eg. adjusting how bright the LED is.

10 pieces pack of crystal white LEDs.

IPX to SMA female cable will allow you easy connection with SMA male antenna to IPX connector which is, for example, a common case with a GSM antenna.

High-quality spare probes for a multimeter.

Ordinary panel switch (pushbutton). Comes in various colors.

This interesting product enables you to control who has is allowed to turn on or turn off a circuit. Namely, in order to change the status of this switch, you need to put the key in the lock and turn it around.

The Shunt Resistor is a special type of resistor with small resistance which allows large currents to pass through it. This is useful for measuring the current in a circuit: due to the Ohm’s law and voltage drop on the shunt resistor, we can know exactly which current passes through it. For example, for this resistor whose maximum current is 50A, the voltage drop at that current will be exactly 75mV (0.075V). Using a precise ADC, we can accurately measure the current of our consumer or power source.

• Max. current: 50A
• Voltage drop for max. current: 75mV
• Dimensions: 120mm x 25mm

The Shunt Resistor is a special type of resistor with small resistance which allows large currents to pass through it. This is useful for measuring the current in a circuit: due to the Ohm’s law and voltage drop on the shunt resistor, we can know exactly which current passes through it. For example, for this resistor whose maximum current is 10A, the voltage drop at that current will be exactly 75mV (0.075V). Using a precise ADC, we can accurately measure the current of our consumer or power source.

• Max. current: 10A
• Voltage drop for max. current: 75mV
• Dimensions: 120mm x 25mm

Every real fan of electronics loves to have things that he knows will be needed in the future. The first and the most basic thing is a set of resistors, but immediately after, there are capacitors. The amount of times the whole project wouldn’t work just cause of one capacitor is too high! This set comes with a total of 120 electrolytic capacitors, with different voltages and capacities.

Panel pushbuttons may look ordinary but may look good as well, as this metal pushbutton with backlight. This pushbutton is waterproof, shock-proof and vandal-proof. Also comes with a backlight in a variety of colors.

Panel pushbuttons may look ordinary but may look good as well, as this metal pushbutton with backlight. This pushbutton is waterproof, shock-proof and vandal-proof. Also comes with a backlight in a variety of colors.

Panel pushbuttons may look ordinary but may look good as well, as this metal pushbutton with backlight. This pushbutton is waterproof, shock-proof and vandal-proof. Also comes with a backlight in a variety of colors.

Panel pushbuttons may look ordinary but may look good as well, as this metal pushbutton with backlight. This pushbutton is waterproof, shock-proof and vandal-proof. Also comes with a backlight in a variety of colors.

The active GPS antenna is the perfect solution for enhancing the GPS signal reception of your device. It features a 3-meter long cable with a standard SMA male connector, providing you with ample length for flexible installation. The antenna’s magnetic base allows for easy and secure mounting on any metal surface, making it ideal for a wide range of applications.

This high-performance antenna operates on a frequency of 1575.42MHz and offers a 28dB of amplification, ensuring a strong and stable GPS signal. With a voltage range of 3V-5V and a low current consumption of 10mA max, it is both efficient and versatile. Its circular (RH) polarization further enhances signal quality, providing you with reliable and accurate positioning data for your projects.

Whether you are building a vehicle tracking system, a drone, or any other project that requires precise GPS data, this active antenna is an excellent choice. Its compatibility with popular platforms like Arduino and Raspberry Pi makes it a go-to component for makers and hobbyists. The compact dimensions of 45mm x 39mm x 13mm allow for seamless integration into your setup.

• Connector: SMA male
• Frequency: 1575.42MHz
• Voltage: 3V-5V
• Current: 10mA max.
• Polarization: circular(RH)
• Amplification: 28dB
• Dimensions: 45mm x 39mm x 13mm